Hot
New
In stock

Master Colour Oil

SKU: WOC.531825US

PRODUCT TYPE: Oil Finish

VENDOR: Woca Denmark

$291.29

WOCA Master Colour Oil provides colour and an oil finish in one step. It penetrates and hardens deep inside the wood.  As a result, wood floors become stronger and better withstand wear. Master Colour Oil contains fine pigments in nine different colours, which can be mixed to create a custom colour.

  • No staining is needed with WOCA Colour Oil, as the colour and finish is done in one step.
  • For custom colours Master Colour Oils may be mixed freely to create any desired colour.

WOCA Master Colour Oil provides a hard wearing oil finish and colour in one application. Suitable for oak, ash, spruce, larch, pine and teak, as well as cork. Master Colour Oil may be used on both unfinished or freshly sanded interior woodwork.

Instructions

It is recommended to use a floor buffer for the oil application. Recommended wood moisture maximum - 12%. The oiling should be done at a minimum temperature of 60º F.

Master Colour Oil Application Instructions

  1. Unfinished flooring or wood should be freshly sanded with grit 100-120. Prep the wood surface with a solution of 1/4 cup Wood Cleaner per gallon water. This step is not optional.
  2. Shake the container of Colour Oil well before and during application. Apply the oil in an even coat with a low nap paint roller onto an area of 100 - 200 sq. ft. Let the floor absorb the oil for 20 minutes. Work the oil into the wood with a red pad either manually or for large areas with a buffer. Polish until the floor appears saturated with oil.
  3. Remove the excess oil with lint free cloths, or scrape with a squeegee onto next section of floor to be oiled. Then buff the floor with lint free cloths under white polishing pads. The floor should not appear wet and no excess oil should be left on the surface after polishing. Continue in sections until the whole floor has been finished.
  4. Wait for 6 - 8 hours, or when dry enough to walk on.  Buff the floor with a white polishing pad and colour oil. If a silk matte surface is required, the finished floor may be buffed with 1 liter of Master Colour Oil to 500 - 600 s.f. of floor. The oil must be polished carefully into the floor. No excess oil should be left on the surface. After 6 - 8 hours, cover walking areas with corrugated cardboard for the 72 hours hardening period. Do not expose the floor to water during the hardening time.
Maintain

Clean with Natural Soap Maintain with Maintenance Gel or  Master Colour Oil, but first clean with Wood Cleaner


Coverage

Coverage: Approximately 120 sqft per liter (softwoods) 150 sqft per liter (hardwoods)

Technical
Product properties
Solid content Approx. 60 %
pH-value
Form
Appearance
Flash point
Density 0.90-0.95 g/ml
Wear
Gloss
Weight:
Fully hard 5-7 days at 20°C and 55% humidity
Viscosity
Mixing ratio
Coverage
Colours 11 colours
Odor
Binder Vegetable oil components
Air humidity
Dilution WOCA Solvent (does not normally need to be diluted).
Sandable after
Re-treatment dry
Drying time 12-24 hours at 68°F
Application tools Paint Roller, 4 mm luv, article no. 88004
Paint roller handle, 25mm, article no. 599650
Telescopic rod, article no. 599651
Pot life
Safety
Disposal Empty containers and residues to be disposed of according to local regulations.
Shelf life 3 years
Packaging 1 L - 2.5 L - 5 L
Pack size:
MAL-code:
Pr. No.:
Storage + 50-68°F. Keep out of reach of children. Must not be exposed to heat (e.g. sunlight). Store frost-free.
Download

WOCA Master Colour Oil Downloads

  • Master Colour Oil Instructions
2.5
1.0
Extra White
Natural
White

Pickup available at 60 Malcolm Road

Usually ready in 24 hours

Master Colour Oil

2.5 / Extra White

American Express
Apple Pay
Diners Club
Discover
Google Pay
Mastercard
Shop Pay
Visa
PRODUCT INFORMATION
PRODUCT INFORMATION

WOCA Master Colour Oil provides colour and an oil finish in one step. It penetrates and hardens deep inside the wood.  As a result, wood floors become stronger and better withstand wear. Master Colour Oil contains fine pigments in nine different colours, which can be mixed to create a custom colour.

  • No staining is needed with WOCA Colour Oil, as the colour and finish is done in one step.
  • For custom colours Master Colour Oils may be mixed freely to create any desired colour.

WOCA Master Colour Oil provides a hard wearing oil finish and colour in one application. Suitable for oak, ash, spruce, larch, pine and teak, as well as cork. Master Colour Oil may be used on both unfinished or freshly sanded interior woodwork.

Instructions

It is recommended to use a floor buffer for the oil application. Recommended wood moisture maximum - 12%. The oiling should be done at a minimum temperature of 60º F.

Master Colour Oil Application Instructions

  1. Unfinished flooring or wood should be freshly sanded with grit 100-120. Prep the wood surface with a solution of 1/4 cup Wood Cleaner per gallon water. This step is not optional.
  2. Shake the container of Colour Oil well before and during application. Apply the oil in an even coat with a low nap paint roller onto an area of 100 - 200 sq. ft. Let the floor absorb the oil for 20 minutes. Work the oil into the wood with a red pad either manually or for large areas with a buffer. Polish until the floor appears saturated with oil.
  3. Remove the excess oil with lint free cloths, or scrape with a squeegee onto next section of floor to be oiled. Then buff the floor with lint free cloths under white polishing pads. The floor should not appear wet and no excess oil should be left on the surface after polishing. Continue in sections until the whole floor has been finished.
  4. Wait for 6 - 8 hours, or when dry enough to walk on.  Buff the floor with a white polishing pad and colour oil. If a silk matte surface is required, the finished floor may be buffed with 1 liter of Master Colour Oil to 500 - 600 s.f. of floor. The oil must be polished carefully into the floor. No excess oil should be left on the surface. After 6 - 8 hours, cover walking areas with corrugated cardboard for the 72 hours hardening period. Do not expose the floor to water during the hardening time.
Maintain

Clean with Natural Soap Maintain with Maintenance Gel or  Master Colour Oil, but first clean with Wood Cleaner


Coverage

Coverage: Approximately 120 sqft per liter (softwoods) 150 sqft per liter (hardwoods)

Technical
Product properties
Solid content Approx. 60 %
pH-value
Form
Appearance
Flash point
Density 0.90-0.95 g/ml
Wear
Gloss
Weight:
Fully hard 5-7 days at 20°C and 55% humidity
Viscosity
Mixing ratio
Coverage
Colours 11 colours
Odor
Binder Vegetable oil components
Air humidity
Dilution WOCA Solvent (does not normally need to be diluted).
Sandable after
Re-treatment dry
Drying time 12-24 hours at 68°F
Application tools Paint Roller, 4 mm luv, article no. 88004
Paint roller handle, 25mm, article no. 599650
Telescopic rod, article no. 599651
Pot life
Safety
Disposal Empty containers and residues to be disposed of according to local regulations.
Shelf life 3 years
Packaging 1 L - 2.5 L - 5 L
Pack size:
MAL-code:
Pr. No.:
Storage + 50-68°F. Keep out of reach of children. Must not be exposed to heat (e.g. sunlight). Store frost-free.
Download

WOCA Master Colour Oil Downloads

  • Master Colour Oil Instructions

WOCA Master Colour Oil provides colour and an oil finish in one step. It penetrates and hardens deep inside the wood.  As a result, wood floors become stronger and better withstand wear. Master Colour Oil contains fine pigments in nine different colours, which can be mixed to create a custom colour.

  • No staining is needed with WOCA Colour Oil, as the colour and finish is done in one step.
  • For custom colours Master Colour Oils may be mixed freely to create any desired colour.

WOCA Master Colour Oil provides a hard wearing oil finish and colour in one application. Suitable for oak, ash, spruce, larch, pine and teak, as well as cork. Master Colour Oil may be used on both unfinished or freshly sanded interior woodwork.

Instructions

It is recommended to use a floor buffer for the oil application. Recommended wood moisture maximum - 12%. The oiling should be done at a minimum temperature of 60º F.

Master Colour Oil Application Instructions

  1. Unfinished flooring or wood should be freshly sanded with grit 100-120. Prep the wood surface with a solution of 1/4 cup Wood Cleaner per gallon water. This step is not optional.
  2. Shake the container of Colour Oil well before and during application. Apply the oil in an even coat with a low nap paint roller onto an area of 100 - 200 sq. ft. Let the floor absorb the oil for 20 minutes. Work the oil into the wood with a red pad either manually or for large areas with a buffer. Polish until the floor appears saturated with oil.
  3. Remove the excess oil with lint free cloths, or scrape with a squeegee onto next section of floor to be oiled. Then buff the floor with lint free cloths under white polishing pads. The floor should not appear wet and no excess oil should be left on the surface after polishing. Continue in sections until the whole floor has been finished.
  4. Wait for 6 - 8 hours, or when dry enough to walk on.  Buff the floor with a white polishing pad and colour oil. If a silk matte surface is required, the finished floor may be buffed with 1 liter of Master Colour Oil to 500 - 600 s.f. of floor. The oil must be polished carefully into the floor. No excess oil should be left on the surface. After 6 - 8 hours, cover walking areas with corrugated cardboard for the 72 hours hardening period. Do not expose the floor to water during the hardening time.
Maintain

Clean with Natural Soap Maintain with Maintenance Gel or  Master Colour Oil, but first clean with Wood Cleaner


Coverage

Coverage: Approximately 120 sqft per liter (softwoods) 150 sqft per liter (hardwoods)

Technical
Product properties
Solid content Approx. 60 %
pH-value
Form
Appearance
Flash point
Density 0.90-0.95 g/ml
Wear
Gloss
Weight:
Fully hard 5-7 days at 20°C and 55% humidity
Viscosity
Mixing ratio
Coverage
Colours 11 colours
Odor
Binder Vegetable oil components
Air humidity
Dilution WOCA Solvent (does not normally need to be diluted).
Sandable after
Re-treatment dry
Drying time 12-24 hours at 68°F
Application tools Paint Roller, 4 mm luv, article no. 88004
Paint roller handle, 25mm, article no. 599650
Telescopic rod, article no. 599651
Pot life
Safety
Disposal Empty containers and residues to be disposed of according to local regulations.
Shelf life 3 years
Packaging 1 L - 2.5 L - 5 L
Pack size:
MAL-code:
Pr. No.:
Storage + 50-68°F. Keep out of reach of children. Must not be exposed to heat (e.g. sunlight). Store frost-free.
Download

WOCA Master Colour Oil Downloads

  • Master Colour Oil Instructions

This is a standard cookie notice which you can easily adapt or disable as you like in the admin. We use cookies to ensure that we give you the best experience on our website.

Master Colour Oil

Master Colour Oil

$291.29
2.5
1.0
Extra White
Natural
White